
Rockstar Sealing
TIME SAVER
Rockstar Time Saver is a water-based sealer specifically formulated for Concrete Pavers, Precast Products, and Natural stone.
- Stops water absorption during grouting and clean up
- Reduces salt transmission, efflorescence, mildew and grout haze
- Durable, fast curing, and non-flammable
- Suits concrete pavers, pre-cast stone products, and natural stone
Designed to:
- Act as a pre-grout release sealer (apply to stone surfaces before grouting).
- Prepare the stone surface for cleaning.
Sweep area to remove dust, building debris i.e plaster, paint, or any contaminant that will inhibit maximum penetration of the sealer. Always test products on a small area first. And allow a 24-hour cure time to determine the ease of application and desired results. One coat of Rockstar Time Saver should be applied with a low-pressure pump or a lambswool applicator. Allow 10 minutes for the product to penetrate the surface then wipe off excess with a clean white dry cloth.
Important: do not allow pre-seal to pool on the surface. The coat coverage rate will vary between 5 and 15m2 depending on the porosity of the material. Allow drying time of around 60 minutes between coats depending on weather and humidity. The surface should be allowed 24 hours to fully cure.
Description
Rockstar TIME SAVER is a water-based Pre-Sealing solution formulated for use on Natural Stone Paving, Concrete Pavers and Terrazzo.
USES
TIME SAVER is applied to the stone or tile surface prior to grouting to reduce permeability and increase the stain resistance of the surface. Excess grout generated during the grouting process can then be easily removed.
BENEFITS
- Environmentally friendly water-based formulation
- Reduces the ingress of water borne staining substances
- Does not inhibit the water-vapour permeability
- Allows grout haze to be easily removed from the stone’s surface
- Rapid curing
- Zero VOC
- Compatible will subsequent penetrating sealers and coatings
PROPERTIES
Appearance and colour………………………………….Milky white liquid
pH …………………………..…………………………..………7-8
Specific Gravity (Water = 1) …………………………..0.98 g/ml
Boiling Point ………………………………………………..100oC
Solubility in Water ………………………………………..Miscible
Flash Point ………………………………………………….Non-flammable
APPLICATION INSTRUCTIONS
- Ensure the surface to be sealed is clean, dry and free of any oils and other surface contaminants.
- Apply TIME SAVER with a lambswool applicator or a low pressure hand sprayer. Ensure an even coat has been applied to the stone surface.
- The product will cure in around 12 hours depending on atmospheric conditions.
COVERAGE
Coverage is dependent on the permeability of the stone or tile and is in the range of 6-15 Mt2 per litre.
PRECAUTIONS
Avoid contact with skin and eyes by wearing suitable protective gloves and eyewear.
CLEANING
Clean all equipment in water.
PACKAGING
TIME SAVER is available in 5 and 20 litre containers.
STORAGE
Keep container tightly closed when not in use. Store in a cool, dry place out of reach of children.
SAFETY
Classified as Non-Hazardous according to criteria of Worksafe Australia. For further detailed information refer to Material Safety Data Sheet.
DISCLAIMER
The advice and information contained herein is based on our best knowledge of the product. We believe the information to be accurate and reliable as at the date supplied, but no representation, guarantee or warranty, expressed or implied, is made to the accuracy, reliability, or completeness of the advice and information. We urge persons receiving this advice and information to make their own determination as to the advice and information’s suitability and completeness for their own particular situation. When in doubt it is always prudent to perform a trial on a scrap section of material, or inconspicuous section of the job to ascertain the products suitability.
Additional information
Size |
1L, 5L, 20L |
---|
Technical Data Sheets
Please access the product information sheet and Material Safety Data Sheet (MSDS) below: